0

Out of 0 Ratings

Owner's of the Black & Decker Cordless Drill RTX-B gave it a score of 0 out of 5. Here's how the scores stacked up:
  • Reliability

    0 out of 5
  • Durability

    0 out of 5
  • Maintenance

    0 out of 5
  • Performance

    0 out of 5
  • Ease of Use

    0 out of 5
of 5
 
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
USE OF EXTENSION CORDS
Make sure the extension cord is in good condition before using. Always use the proper size
extension cords with the tool that is, proper wire size for various lengths of cord and heavy
enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. For proper size cords see chart
below.
SPINDLE LOCK LEVER
TURN OFF AND UNPLUG TOOL FROM POWER SUPPLY.
Fig.1 shows the ON/OFF switch and the spindle lock lever. To lock the spindle for changing
accessories, pull back on the spindle lock lever as shown in Figure 2. With the lever in the full
back position the spindle will lock. Install or remove the accessories as directed in this
manual. Release the spindle lock lever and youre finished.
ON/OFF SWITCH
To turn the tool ON, slide the switch button forward. The tool will immediately run at the speed
which is selected. Do not attempt to start tool with spindle lock engaged. It will not run.
SPEED SELECTION
To operate the tool, select the speed setting you wish with the speed wheel, shown in Fig 3,
and slide the ON/OFF switch forward. The speed setting can be adjusted either with the tool
on or off.
CAUTION: Because the RTX has a separate speed wheel for setting the speed (8,000 -
30,000 RPM), the tool will start at the speed where the speed wheel is set. Be sure switch is
fully OFF before plugging in.
The numbered positions,1 through 6 inscribed on the switch speed wheel, do not indicate
any precise speed but are good reference points. The higher the number, the higher the tool
speed.
The approximate speed at each setting is:
SPEED SETTING 1 2 3 4 5 6
APPROX. SPEED 8,000 12,000 19,000 24,000 28,000 30,000
(Actual RPMs on your tool may vary.)
Be sure to select the proper speed for your rotary tool operation. The following chart
provides a speed guide for various operations.
If in doubt about the proper speed for your operation, test the performance at low speed
settings and gradually increase until a comfortable speed is found.
Cutting Metal . . . . . 5-6 Deburring . . . . . . . 4-5
Sanding Wood . . . . 5-6 Stripping Metal . . . 4-5
Sharpening. . . . . . . 3-5 Engraving Metal . . 4-5
Polishing . . . . . . . . 1-2 Drilling Holes. . . . . 4-5
Removing Rust. . . . 1-2
CAUTION: Never exceed the speed rating of the accessory being used.
CHANGING ACCESSORIES
Accessories are held in place by a collet and collet nut as shown in Figure 4.
To insert an accessory:
1. Turn off tool, allow it to come to a complete stop and disconnect from the power supply.
2. Pull back on the spindle lock lever (see Fig. 2) and grasp the collet nut.
3. Turn the collet nut counter-clockwise as shown in Fig. 5 until it is loose.
4. Insert the new accessory into the collet as far as it will go.
5. Tighten (clockwise) the collet nut securely. NOTE: The collet was designed to be hand
tightened and loosened only. Accessories naturally self tighten during use. A wrench is
provided with the tool for loosening. You should never need to tighten the collet nut with
the wrench. If a wrench is needed, use only the wrench provided. Do not use tools that
will mar the finish and could break the collet. Always ensure there is some accessory in
the collet before tightening. Tightening an empty collet can crack it.
6. Release the spindle lock lever and youre finished.
7. If an accessory causes vibration it can usually be improved by loosening the collet nut,
pushing the accessory in as far as it will go and rotating it 1/4 turn then retightening the
collet.
CHANGING THE COLLET
Some accessories require different sized collets. The two collets used with Black & Decker
accessories are 1/8" (used for most accessories) and 3/32". Ensure your collet size
matches your accessory.
To change the collet:
1. Turn off tool, allow it to come to a complete stop and disconnect from power supply.
2. Pull back on the spindle lock lever (see Fig. 2) and grasp the collet nut.
3. Turn the collet nut counter-clockwise and remove the collet nut and the collet from the
threaded spindle (see Fig. 4).
4. Insert the new collet into the spindle.
5. Screw on the collet nut.
6. Release the spindle lock.
USING THE ROTARY TOOL
WARNING: Always wear eye protection.
When operating the tool be sure to hold it securely. For detail work, grip the contoured area
at the front of the tool, near the spindle. Before beginning a project, practice using the tool
on some scrap material until you get the "feel" of the tool. The rotary tool is small and easy to
use but dont be fooled; its a real power tool and should be handled carefully and properly
as described in this manual. Dont overload the tool. Performance is enhanced by letting the
tool do the work.
FLEXIBLE SHAFT RT5100 FLEXIBLE ROTARY TOOL EXTENDER
(Available as a separate accessory and included with catalog number RTX-2 only)
FLEXIBLE SHAFT INSTALLATION INSTRUCTIONS
1. Turn off tool, allow it to come to a complete stop and disconnect from power supply.
2. Remove the collet nut and collet from the tool by first pulling back on the spindle lock
lever and grasping the collet nut (Fig.2).
3. Turn the collet nut counter-clockwise and remove the collet nut and the collet from the
threaded spindle (see Fig. 4).Release the spindle lock.
4. Remove the silver housing cap (Fig.4) by turning counterclockwise.
5. Locate the driver nut and thread it onto the motor shaft (Fig. 6).
6. Screw the F
LEXIBLE SHAFT onto the rotary tool as shown in Fig. 7 insuring that the rotating
center core engages the square hole socket in the driver nut (Fig. 7). NOTE: Use caution
when screwing the metal housing of the shaft onto the threaded portion of the rotary tool.
Avoid cross threading.
7. The F
LEXIBLE SHAFT is now ready for use. To insert an accessory, Turn off tool, allow it to
come to a complete stop and disconnect from power supply. Place the provided lock pin
into the opening in the FLEXIBLE SHAFT hand piece and rotate collet nut until lockpin
engages hole in spindle (Fig. 8). With the shaft locked, turn the collet nut counter-clock-
wise to loosen. Insert the accessory completely into the collet to avoid wobbling. Tighten
collet nut securely by hand. Remove lock pin.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
8. The Flexible Shaft collet can be changed as described in the Changing the Collet sec-
tion.
IMPORTANT: Avoid using the Flexible Shaft with a sharp bend as shown in Fig. 9. A radius
of 6" or larger is recommended. A tool hanger (Fig. 4) is provided to hang the tool when using
the flex shaft. The hanger secures the tool and helps avoid sharp bends on the flex shaft.
NOTE: The rotating center core can come out of the F
LEXIBLE SHAFT. This is not a problem.
Simply reinsert it into the FLEXIBLE SHAFT. If the center core gets dirty, wipe it off and apply a
very light film of high temperature grease. The square drive of the center core may not
engage the hand piece. To get it to engage, apply a light force to the tip of the center core
while rotating the handpiece collet nut.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service organizations, always using identical replacement
parts. Unit contains no user serviceable parts inside.
ACCESSORIES
Black & Decker offers a large selection of accessories available at your local dealer or
authorized service center at extra cost. Only Black & Decker accessories are recommended
for use in the RTX or B&D Flexible Shaft.
If you need assistance regarding accessories, please call: 1-800-54-HOW TO (544-6986).
CAUTION: Use only those accessories rated at 30,000 RPM or greater. Exception: Do
not operate wire brushes, bristle brushes, diamond dome sander, or 1-1/4 diamond wheels
at speeds greater than 15,000 RPM (speed setting #2). Never exceed the speed rating of the
accessory being used.
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact
the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under "ToolsElectric"
or call: 1-800-54-HOW TO (544-6986).
FULL FIVE-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for five years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailers policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under
"ToolsElectric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center.
NOTE: This tool is designed, manufactured and tested to meet or exceed the needs of the
do-it-yourselfer in the execution of projects and repairs in and around the home. With proper
use it will provide the home owner with years of service. However, if you use tools for a living
and use this product or any of Black & Deckers other Consumer Home Use tools ON THE
JOBSITE you should know that they CANNOT BE COVERED UNDER OUR WARRANTY.
Modèle RTX
GUIDE D’UTILISATION
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAI-
SON PRIÈRE DE COMPOSER
1 800 544-6986
CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
RENSEIGNEMENTS IMPORTANTS
On ne doit jamais serrer l’écrou de la douille de serrage sans y avoir dabord inséré
une mèche ou un autre accessoire.
Attendre que loutil se soit complètement immobilisé avant dengager le dispositif de
verrouillage de la broche.
MESURES DE SÉCURITÉ
AVERTISSEMENT : Lire et comprendre toutes les directives. Le non-respect de toutes
les directives suivantes présente des risques de secousses électriques, d'incendie ou de
blessures graves.
CONSERVER CES MESURES.
ZONE DE TRAVAIL
S'assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et
des endroits sombres présentent des risques d'accidents.
Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme
celles dégagées par des liquides, des gaz ou des poussières inflammables). Les
étincelles générées par le moteur des outils électriques peuvent enflammer les poussières
ou les vapeurs.
Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu'on utilise
un outil électrique. Une distraction peut entraîner la perte de maîtrise de l'outil.
MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ
Les outils à double isolation comportent une fiche polarisée (une lame plus large que
l'autre). La fiche n'entre que d'une façon dans une prise polarisée. Lorsque la fiche
n'entre pas à fond dans la prise, essayer de nouveau après avoir inversé les broches
de la fiche. Si la fiche n'entre toujours pas dans la prise, communiquer avec un
électricien certifié afin de faire installer une prise polarisée. Ne modifier en aucune
façon la fiche. La double isolation élimine le besoin d'un cordon trifilaire mis à la terre et
d'un système d'alimentation mis à la terre.
Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs,
des cuisinières et des réfrigérateurs. Les risques de secousses électriques sont plus
élevés si le corps de l'utilisateur est mis à la terre.
Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration
d'eau dans l'outil augmente les risques de secousses électriques.
Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter
l'outil ni tirer sur le cordon pour débrancher l'outil. Éloigner le cordon des sources de
chaleur, des flaques d'huile, des arêtes tranchantes et des pièces mobiles.
Remplacer immédiatement les cordons endommagés. Les cordons endommagés
augmentent les risques de secousses électriques.
Lorsqu'on utilise un outil électrique à l'extérieur, se servir d'un cordon de rallonge
prévu pour l'extérieur, portant la mention "W-A" ou "W". Ces cordons sont conçus pour
servir à l'extérieur et minimisent les risques de secousses électriques.
SÉCURITÉ PERSONNELLE
Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu'on utilise un outil