Black & Decker Power Screwdriver LI3100 User Manual

4.0

Out of 5 Ratings

Owner's of the Black & Decker Power Screwdriver LI3100 gave it a score of 4.0 out of 5. Here's how the scores stacked up:

  • Reliability

    4.0 out of 5

  • Durability

    3.6 out of 5

  • Maintenance

    3.8 out of 5

  • Performance

    4.0 out of 5

  • Ease of Use

    4.8 out of 5
of 32
 
8
• Do not use screwdriver as a pry bar in any position.
• To avoid screwdriver being turned on accidentally, do not carry in your pocket.
LED LIGHT
A light (3) is built-in to the screwdriver below the spindle (4). To use the light without the
spindle turning, place the forward / reverse selector (2) in the neutral position and
squeeze the trigger.
DRILLING
• Insert the appropriate hex shank drill bit.
• Select forward rotation.
NOTE: When drilling, the bit may become disconnected from the spindle upon
withdrawing it from the material. Should this occur, the bit can be removed by re-inserting
the hex shank into the spindle and running the tool in the reverse direction.
GENERAL DRILLING TIPS
• This tool is not recommended for drilling in masonry.
• Use sharp drill bits only.
• Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and
should be pulled out frequently when drilling to clear chips from the flutes.
• Support and secure work properly, as instructed in the safety Instructions.
• Use appropriate and required safety equipment, as instructed in the safety instructions.
• Secure and maintain work area, as instructed in the safety instructions.
• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting
but not so much as to stall the motor or deflect the bit.
• Hold the tool firmly to control its twisting action.
• DO NOT CLICK THE TRIGGER OF A STALLED TOOL OFF AND ON IN AN ATTEMPT
TO START IT. DAMAGE TO THE TOOL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through last
part of hole.
• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce
jamming.
• Make sure switch turns tool on and off.
WARNING: It is important to support work properly and to hold the tool firmly to prevent
loss of control which could cause personal injury.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service personnel, always using identical replacement
parts.
BATTERY REMOVAL AND DISPOSAL
This product uses lithium-ion rechargeable and recyclable batteries. When the batteries
no longer hold a charge, they should be removed from the product and recycled. They
must not be incinerated or composited.
The batteries can be taken for disposal to a Black & Decker, Company-Owned or
Authorized Service Center. Some local retailers are also participating in a national
recycling program (see “RBRC
TM
Seal”). Call your local retailer for details. If you bring
the batteries to a Black & Decker Company-Owned or Authorized Service Center, the
Center will arrange to recycle old batteries. Or, contact your local municipality for proper
disposal instructions in your city/town.
To remove the battery pack for disposal:
1.) First, before attempting to disassemble the product, turn it on and run it in either
direction until it stops to ensure a complete discharge of the batteries.
2.) Remove the screws in the product housing and lift the housing half from the tool.
3.) Disconnect the terminal clips from the batteries and lift the batteries out.
4.) Place the battery in suitable packaging to prevent a short circuit of the battery
terminals.
5.) Dispose of batteries as per recommended guidelines.
90550370 LI3100.qxd 5/4/09 8:00 AM Page 8

   Find Your Products By Category