Black & Decker Router BDCMTR User Manual

3.2

Out of 2 Ratings

Owner's of the Black & Decker Router BDCMTR gave it a score of 3.2 out of 5. Here's how the scores stacked up:

  • Reliability

    4.0 out of 5

  • Durability

    3.0 out of 5

  • Maintenance

    3.0 out of 5

  • Performance

    3.0 out of 5

  • Ease of Use

    3.0 out of 5
of 24
 
6
FEEDING SPEED AND RATE OF CUT
Variation between materials and bit configurations dictates a wide variety of feed rates.
Experience is the best measure for determining feed rate. Become familiar with the sound and
feel of the router by making practice cuts in scrap material.
The router bit rotates at a very high speed and may heat up if the router is moved too slowly through
the wood and cause burn marks. Feeding the router too fast or trying to remove too much material in
a single pass will overload the motor. Use two or more passes for extra-large cuts (over 1/8” deep),
especially in hard woods.
HINTS FOR OPTIMUM USE
When working on outside edges, move the tool counterclockwise (gure E). When working on
inside edges, move the tool clockwise.
• Usepilot(ballbearing)routerbitsforedgeprofilecutting.
• UseHSS(highspeedsteel)routerbitsforsoftwood.
• UseTCT(tungstencarbidetipped)routerbitsforhardwood.
• Notrecommendedforplungecutting.
TROUBLESHOOTING
Problem Possible Cause Possible Solution
•Unitwillnotstart. •Attachmentisnotsecured. •Makecertaintheattachmentisfully
pushed into the Power Unit.
For assistance with your product, visit our website www.blackanddecker.com for the location
oftheservicecenternearestyouorcalltheBLACK&DECKERhelplineat1-800-544-6986.
NOTE: Refer to Power Unit instruction manual for troubleshooting solutions regarding opera-
tion of the Power Unit.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized service
centers or other qualified service personnel, always using identical replacement parts.
ACCESSORIES
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Recommended accessories for use with your tool are available from your local dealer or authorized
service center. If you need assistance regarding accessories, please call: 1-800-544-6986.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandreceiver.
•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

   Find Your Products By Category